Polyplanar ME-400D User Manual download pdf

WARRA

NTY INFORMATION

OUTPUT POWER (max) @ 14.4V / 4Ω / 2

Channel

800 W x 2 CH

Distortion (T.H.D) <0.03%

Signal to Noise Ratio 102dB

Channel Separation 56dB

Input Sensitivity 200mV - 6.0V

LOW PASS FILTER / slope 50 Hz - 5000Hz/12dB

HIGH PASS FILTER / slope 20Hz - 4000Hz/12dB

FUSE RATING 25A x 3

DIMENSION ( L x W x H )in/mm

11”/280mm x

6.7”/170mm x 1.7”/45mm

Nominal Current draw:100W/ 4 OHM 40A

Max current draw 90A

NOTE: Specification & design subject to change without notice for

improvements.

This unit is warranted to be free of defects in material and workmanship for a

period of one year. Warranty is subject to proper installation and operation

within the published specifications. Except as provided below, Poly Planar

will repair or replace, at its discretion, any product returned prepaid to our

facility and determined to be defective. Poly Planar is not liable for

consequential damages

LIMITS OF LIABILITY

Poly Planar warranty does not cover damage occurred in transit, accident,

abuse, misuse, negligence, fire, flood, lightning or unauthorized service. This

warranty assumes no responsibility for damages incurred during installation of

this equipment. This warranty covers normal consumer use only. In no event

shall Poly Planar be liable for special, incidental, or consequential damages.

To obtain service under this warranty, please call Poly-Planar for a RETURN

AUTHORIZATION NUMBER.

poly-planar, inc.

Maryland USA

(410) 761-4000

www.polyplanar.com

PRECAUTIONS : READ FIRST!

ME-400D OWNER’S MANUAL

4 CHANNEL CLASS D POWER AMP

•

• The negative battery terminal must be disconnected before any

electrical connections are made.

• If after reading the directions you feel uncomfortable about

installing the amplifier in your vessel, or not equipped or competent

to do so, you should have the amplifier installed by an authorized

installer

• Be sure to choose a location that provides substantial ventilation for

the amplifier. The location chosen should provide at least 2 inch of

clearance above the amplifier for adequate ventilation.

• If the amplifier is to be mounted vertically be sure that it is in a place

where adequate air will flow along the length of its heat sink fins for

cooling.

• NEVER mount the amplifier up side down, this will cause the heat to

rise back into the amplifier causing thermal shutdown or possible

permanent damage.

• Be sure to mount the amplifier to a strong, solid surface which will not

give way under the stress of waves pounding the hull.

• Make sure that the mounting screws will not penetrate through the

hull or into wiring or control cables.

• NEVER ground the speaker leads and NEVER allow the speaker leads

to come in contact with each other. The speaker wire should be at

least 16 gauge or lower.

• NEVER operate the amplifier without the proper power and ground

wire 10 gauge minimum.

1 2 3 4

ME-400D OWNER’S MANUAL 1

Summary of Contents

Page 1 - ME-400D OWNER’S MANUAL

8WARRANTY INFORMATIONOUTPUT POWER (max) @ 14.4V / 4Ω / 2 Channel 800 W x 2 CH Distortion (T.H.D) <0.03% Signal to Noise Ratio 102dB Cha

Page 2

2FRONT PANEL• NEVER operate the amplifier without proper fusing. Fuse holder must be located within 2 feet from the battery. This fuse is to protect

Page 3

64-CHANNEL CONFIGURATION 2- CHANNEL CONFIGURATION 31. POWER TERMINAL When the power supply lead or g

Page 4

4REAR PANEL 1. REAR RCA INPUTS -for rear left and rear right channel 2. LOW PASS FREQUENCY RANGE SWITCH (REAR) -switches the rear

Comments to this Manuals

No comments

Polyplanar ME-400D User Manual

Browse online or download User Manual for Receivers and Amplifiers Polyplanar ME-400D. PolyPlanar ME-400D User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Polyplanar ME-400D